Book Appointment Now

 

 

Were you searching for know-how on Tools You Need to Install a New Bathtub ?

Mounting a bathtub isn't exactly rocket science, however it does call for strong plumbing, woodworking, and occasionally, tiling skills. Replacing an old bathtub with a new one is likewise a reasonably hard task. If the old bathtub is readily accessible, the project can move rapidly; if you need to open up a wall surface to get rid of the old bathtub and also place the brand-new bath tub, the task is much harder. In either case, the project is within a home handyman's skills, although you will need a helper to move out the old tub and set in the new one. Make sure you have qualified yourself for the job and are comfortable attempting it. Rather than hiring a contractor to take over a halfway-completed project, it is far better to take into consideration using one prior to you start. Opportunities are you might require a professional plumber to make tube connections.
This article will certainly assist you set up a new bathtub in your bathroom if you have currently acquired a brand-new bathtub as well as don't need to transform the setup of your previous water pipes.
Your tools and product list need to consist of the following:

 

• New Bath tub


• Hammer


• Pipeline Wrenches


• Prybar


• Shatterproof glass


• Degree


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Knife


• Measuring tape


• Pipeline Caps


 

Removing Old Taps

If you need to change old faucets with new ones as a part of your installation, after that the first thing you must do is detach the water supply. After doing so, activate the faucets to drain pipes any type of water remaining in the system. The process of getting rid of the existing taps can be quite bothersome because of the restricted access that is usually the situation.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipelines to the taps. Have a cloth all set for the staying water that will come from the pipelines. When the supply pipes have been gotten rid of, utilize the same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning during this procedure. Once the faucets have been eliminated, the holes in the bath/basin will need to be cleaned up of any old securing compound.
Prior to moving on to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.

 

 

Fitting New Touches

If the tails of the new taps are plastic, after that you will require a plastic port to stop damage to the string. One end of the connector fits on the plastic tail of the faucet and the various other end provides a link to the current supply pipes.
If you require to fit a monobloc, then you will certainly require minimizing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, place the tap in the installing opening in the bath/basin guaranteeing that the washing machines are in location in between the tap as well as the sink. Protect the faucet in place with the producer given backnut. Once the faucet is firmly in place, the supply pipes can be attached to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with normal faucet adapters. The former type must be attached to the tap finishes first, tightening up just by hand. The supply pipes can later be linked to the various other end. Tighten both ends with a spanner after both ends have been linked.

 

 

Mounting the Bathtub

Using the two wood boards under its feet, position the bathtub in the needed setting. The wood boards are helpful in uniformly spreading out the weight of the bath tub over the location of the boards rather than concentrating all the weight onto four small points.
The next goal is to guarantee that the tub is leveled all round. This can be attained by examining the spirit level and changing the feet on the tub till the level reviews level.
To install faucets, fit all-time low of the outermost adaptable tap connector to the suitable supply pipe by making a compression join; after that do the exact same for the various other faucet.
Activate the water and check all joints and new pipework for leaks and tighten them if required. Fill up the tub as well as additionally examine the overflow electrical outlet and the normal outlet for leakages.
Ultimately, deal with the bathroom paneling as defined in the maker's user's manual. Tiling and also securing around the tub must wait up until the tub has been utilized a minimum of once as this will settle it into its last placement.

 

 

Planning for the Setup

First of all, the sustaining structure provided with the bathroom ought to be fitted (if needed) according to the producer's directions. Next, fit the taps or mixer to the bathtub. When fitting the faucet block, it is necessary to see to it that if the faucet includes a plastic washer, it is fitted between the bathroom as well as the faucets. On a plastic bath, it is also sensible to fit a sustaining plate under the faucets system to prevent strain on the bath tub.
Fit the versatile tap connectors to the bottom of both faucets utilizing 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make sure you make use of all of the supplied washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bath must now prepare to be fitted in its last setting.

 

 

Tiling Around the Bathtub

In the location where the bath fulfills the tile, it is essential to seal the accompanies a silicone rubber caulking. This is very important as the fitting can relocate enough to split a rigid seal, triggering the water to penetrate the wall surface between the bathroom and the tiling, causing complications with wetness and feasible leaks to the ceiling listed below.
You can pick from a range of coloured sealers to blend in your components and installations. They are sold in tubes as well as cartridges, as well as can sealing voids up to a size of 3mm (1/8 inch). If you have a larger space to load, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to always fill up the bathtub with water prior to sealing, to enable the activity experienced when the tub remains in usage. The sealer can crack relatively very early if you do not take into consideration this activity before sealing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally conveniently available on the marketplace. It is suggested to fit the tiles utilizing waterproof or water-proof glue and grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

As a serious person who reads about How to Install a Bathtub, I thought sharing that excerpt was really helpful. Don't hesitate to take the opportunity to share this content if you liked it. We appreciate reading our article about How to Install a Bathtub.

Apply Now